散射对高温气体-碳黑颗粒混合物辐射传输的影响

基于全光谱k分布(Full spectrum k distribution,FSK)模型、MIE理论和有限体积法(Finite volume method,FVM),构建了均温、均质辐射参与性气体-碳黑颗粒混合物介质热辐射传输模型,并分析了碳黑不同尺寸、不同体积浓度以及介质不同路径长度和不同温度条件下,因忽略碳黑颗粒散射所导致的介质热辐射传输特性(如辐射热流、辐射源项)的计算误差。研究结果表明:体积分数不变,增大粒径,计算误差呈现出先增大后减小的趋势;数密度不变,增大粒径,或者粒径不变,增大体积分数,均将使得计算误差相应增大;粒径、体积分数不变,增大路径长度,或者升高介质温度,均将增大计算误差。通常对于含有大颗粒、高碳黑浓度的辐射参与性气体-碳黑颗粒混合物介质,碳黑颗粒散射不能忽略。     

Modeling the effects of green alternative on heat island mitigation of a meso level town,West Bengal,India

Urban heat island (UHI) is emerged as a ubiquitous phenomenon that affects the outdoor thermal comfort. Hence urban microclimatic studies using numeric simulation software to find out adaption strategies are attracting the great attention of researchers and policymaker. Number of scientists carried out their research on this topic using different tools and technique whereas ENVI-met model is the most widely used simulation tools. The present study intended to examine the implication of green infrastructure of the town on enhanced microclimatic condition and to evaluate the best suitable mitigation strategy modelling cool city with ENVI-met software (V4). Five greening condition such as existing UHI condition (C1), 100% greening of roof (C2), 100% greening of roof and walls (C3), 50% greening of roof and walls (C4) and: Plantation at suitable area with 50% greening of roof and walls (C5) have been taken into consideration for the microclimate simulation for all three selected sites. Among these five conditions, C3 for the open mid-rise and compact low-rise, C5 for the open low-rise are identified as one of the most suitable strategies which can reduce the air temperature of peak hours by 2.6 °C, 1.33 °C and 1.87 °C respectively. These models are validated by simple linear regression between simulated and existing air temperature in case of existing UHI condition (C1) and in all the cases coefficient of determination value is high such as for open mid-rise, compact low-rise and open low-rise, it is 0.92, 0.92 and 0.75 respectively. Therefore it can be concluded that the application of those strategies can improve the urban thermal environment as well as the outdoor thermal comfort of English bazaar Town and its surroundings.     

Mapping mean lake surface from satellite altimetry and GPS kinematic surveys

Lake water height is a key variable in water cycle and climate change studies, which is achievable using satellite altimetry constellation. A method based on data processing of altimetry from several satellites has been developed to interpolate mean lake surface (MLS) over a set of 22 big lakes distributed on the Earth. It has been applied on nadir radar altimeters in Low Resolution Mode (LRM: Jason-3, Saral/AltiKa, CryoSat-2) in Synthetic Aperture Radar (SAR) mode (Sentinel-3A), and in SAR interferometric (SARin) mode (CryoSat-2), and on laser altimetry (ICESat). Validation of the method has been performed using a set of kinematic GPS height profiles from 18 field campaigns over the lake Issykkul, by comparison of altimetry’s height at crossover points for the other lakes and using the laser altimetry on ICESat-2 mission. The precision reached ranges from 3 to 7 cm RMS (Root Mean Square) depending on the lakes. Currently, lake water level inferred from satellite altimetry is provided with respect to an ellipsoid. Ellipsoidal heights are converted into orthométric heights using geoid models interpolated along the satellite tracks. These global geoid models were inferred from geodetic satellite missions coupled with absolute and regional anomaly gravity data sets spread over the Earth. However, the spatial resolution of the current geoid models does not allow capturing short wavelength undulations that may reach decimeters in mountaineering regions or for rift lakes (Baikal, Issykkul, Malawi, Tanganika). We interpolate in this work the geoid height anomalies with three recent geoid models, the EGM2008, XGM2016 and EIGEN-6C4d, and compare them with the Mean Surface of 22 lakes calculated using satellite altimetry. Assuming that MLS mimics the local undulations of the geoid, our study shows that over a large set of lakes (in East Africa, Andean mountain and Central Asia), short wavelength undulations of the geoid in poorly sampled areas can be derived using satellite altimetry. The models used in this study present very similar geographical patterns when compared to MLS. The precision of the models largely depends on the location of the lakes and is about 18 cm, in average over the Earth. MLS can serve as a validation dataset for any future geoid model. It will also be useful for validation of the future mission SWOT (Surface Water and Ocean Topography) which will measure and map water heights over the lakes with a high horizontal resolution of 250 by 250 m.     

Substitution of satellite-based land surface temperature defective data using GSP method

Land surface temperature (LST) as an important environmental variable provides valuable information for earth environmental system modelling. Currently, LST is obtained through satellite thermal sensors at various spatial and temporal resolutions. Although spatially continuous satellite-based LST measurements are intended to overcome the shortcomings of sparse ground-based LST measurements, LST images often contain anomalous values due to the existence of clouds or sensor malfunctioning. The problem becomes more serious where the users deal with high spatial resolution characterized by low temporal resolution. This study examines the capability of a newly developed graph signal processing (GSP) method using two-dimensional single-date thermal data. For this purpose, four Landsat/TIRS datasets are analyzed. The data of five elliptical regions on thermal images are eliminated and then reconstructed through the GSP method and using the LST values of the enclosing rectangles containing the ellipsoids. The results indicate that the temperature variation determined by the GSP method generally conforms to the original image LST values. According to a correlation test conducted on the original image LST and those obtained through the GSP method, the values vary from 58% to 95%, which is an above-the-average rate (RMSE from 0.69 to 2.27). The statistical analysis of the original image LST in both the elliptical regions and the enclosing rectangles containing the ellipsoids indicates that an increase in the variance of LST data causes an increased error in the calculation of temperature by the GSP method, and vice versa. The results of the analysis of variance (ANOVA) and Duncan test indicated that an increase in the number of the non-zero spectral bins would result in increased RMSE values for all the dates and the regions. Moreover, the model errors were significant at the 0.05 level across all the image date and five elliptical study regions. Based on the results, the use of this method is recommended for the reconstruction of LST missing values, where dissimilarity of atmospheric conditions limits the use of other methods that depend on the time series data of various dates and a great deal of data calculation.     

AP聚类改进免疫算法用于航空发动机故障诊断

在免疫算法训练过程中引入近邻传播(AP)聚类与熵权法,对训练样本进行聚类与权值计算,将权值引入免疫算法中样本选择阈值的计算,以解决训练过程采用固定选择阈值所造成的检测器在部分区域过拟合,部分区域欠拟合的问题。结果表明:改进的免疫算法用于典型非线性函数的寻优时,迭代性能均优于传统免疫算法,并在大部分情况下优于粒子群算法与量子遗传算法,在进行某型发动机故障诊断的实例实验时,改进后的算法的诊断准确率达到98.06%,高于传统免疫算法的92.60%。      

基于变马赫数的五孔探针三维插值方法

探讨了五孔探针气动数据的插值方法,为提高插值精度,开发了基于传统线性插值法的三维线性插值法。该方法把同一探针在不同马赫数下的校准图形成三维数据库,将实验数据通过三维图进行插值。并使用改进前后的两种插值方法分别对校准风洞测得的数据进行整理,对比结果证明:在实验工况连续变化的情况下,三维线性插值法在插值精度上要优于传统线性插值法。特别是在来流马赫数变化较大时,该方法可以改善单一校准文件处理造成的数据精度问题,可用于自动化流场采集系统,为流场高速高精度采集奠定基础。     

对策论在雷达电子战效能评估中的应用

介绍了对策论的基本内容和分析方法,包括对策论所涉及问题的要素和分类.指出了对策论在雷达电子战效能评估中应用的可行性和必要性.分析了电子对抗博弈双方采取不同对抗技术措施的得益矩阵,并在此得益矩阵的基础上,重点研究了对策论在电子对抗效能评估过程中的应用.     

含有任意多个椭圆孔弹性板的应力场计算

本文应用弹性力学的复变函数理论,用多保角变换的方法,导出了含有任意多个椭圆孔的无限大弹性板多复变量应力函数的表达式。每个孔的大小、位置和孔边作用的载荷均为任意指定。板的无限远处作用有和坐标轴方向一致的均匀拉压载荷P_x,P_y和均匀剪切载荷P_(xy)。并在孔边进行复Fourier级数展开,用待定系数法确定应力函数的未知系数,从而计算弹性板的应力场。编制了相应的FORTRAN77标准化程序,进行了考题和算例分析,给出了级数的收敛状况和孔边周向应力的分布图。     

现代激励理论在规范地方政府行为中的作用研究

分析现代激励理论在研究地方政府行为中的作用，并运用现代激励理论提出了规范地方政府经济行为的若干建议。     

钣金制件表面的相贯线求作方法

本文提出钣金制件表面相贯线求作的新方法。